Set construction and custom builds from photon: we plan DJ booths, lighting elements, steel transport dollies for lighting sets, rear structures for LED walls, risers and stairs in 3D and build them from wood and steel in our own workshop – ready for touring, with built-in lighting and from one source together with the event technology.
Decks, truss and rigging for your set: see stage technology →
SET CONSTRUCTION BY photon
If a part cannot be bought the way you need it, we build it ourselves: DJ booths, lighting elements, steel transport dollies for lighting sets, rear structures for LED walls, risers, stairs and custom pieces for tours and shows. We plan every part in 3D down to the cutting plan and make it in our workshop from multiplex, film-faced plywood and welded steel.
Because construction and lighting come together at photon, we think about fixtures, power and signal from the start: the lights sit permanently in the set, cables are pre-wired, and the load plan for the truck is part of the planning.
DJ booths and CDJ boards
Made to measure, pre-wired, with a secure hold for the players.
Lighting elements on castors
Fixtures fixed in the set, straight from the truck into position.
Risers and stairs
Film-faced plywood steps on welded steel frames.
Steel transport dollies for lighting sets
Fixtures stay mounted and roll onto the stage ready to go – with brackets and mounts made to measure.
Planned for touring
With a load plan for the truck and faster setup and load-out.
Custom pieces to measure
Acrylic frames, fascia panels, cases – whatever else the set needs.
In brief
Set construction covers everything that shapes the look of a show: elements, risers, stairs and add-ons, often with the lighting sitting on or inside them. Custom builds are one-off pieces made to measure, from a DJ booth to a bracket for a single fixture.
Staging with decks, truss and rigging from our rental stock, planned with structural calculations, is covered under stage technology:
Two ways to your set
Set and technology
Construction, lighting, sound and video from one source
We plan the set together with the technology, build it in our workshop and look after it on tour – with set construction, lighting and systems engineering from our own team.
One-off piece or complete set
Every set is a one-off: size, materials, built-in lighting and transport define the effort – there is no honest flat “from X euros” for this. After your enquiry you receive a firm quote.
We also build single pieces: a DJ booth, a riser, a bracket – from your sketch or our drawing.
Read more
A sketch, photos or dimensions are enough to start: what the piece is for, how often it is set up and taken down, which lighting goes into it and how it will be transported. We clarify the rest in a conversation.
Our warehouse with its own vehicles is in Wesseling between Cologne and Bonn – set and technology travel from there together to your event, throughout Germany.
From plan to set
It often starts with a sketch in a notebook. That becomes a 3D model with drawings for every part, down to the cutting plan. That way dimensions, fixtures, cable routes and transport fit together before anything is built.


Left: the drawing of the CDJ board for David Puentez; right: the finished DJ booth on the under-lit grating decks.
Read more
Dimensions, materials and every detail. For the CDJ board for David Puentez, for example: edges routed round and sanded, wooden brackets reinforcing the fascia and a 6 mm wooden rail around the whole DJ set so the players cannot slip.


Steel frames from our own workshop, stairs with film-faced plywood steps.
Fixtures sit permanently on the elements and travel with them; on castors, the set goes from the truck straight into position. Power and signal are pre-wired so setup is faster.


Left: the elevation of the lighting elements for the Lumpenpack tour 2026; right: live at Turbinenhalle Oberhausen (photo: kasama_media).
For Das Lumpenpack's 2026 tour we drew the elements with permanently mounted moving heads, including a load plan showing how the dollies stand in the truck: Lumpenpack tour 2026
For David Puentez's More Goes Not Tour 2025 we designed the entire rear structure of the see-through LED wall so that setup is fast – plus under-lit grating decks and a CDJ board with cable management from our workshop: More Goes Not Tour 2025
See also:
Read more
On the Lumpenpack tour 2026, technical management, lighting systems engineering, media technology and set construction from our team were on the road: 14 shows in eleven venues, including four cities on four consecutive days.
The custom-build concept already proved itself on Das Lumpenpack's Nie wieder Wach tour 2025: pre-made cable looms and standardised modules made the daily setup predictable.
As a master craftsman business with 16 employees and our own warehouse in Wesseling, we plan set, lighting, sound and video from one source – from the first sketch to load-out.
FAQ